Jump to content

Recommended Posts

I’m thinking about getting an airbrush for priming my minis (Similar to Sarastro’s method). I was thinking about buying a 50$ airbrush kit online that comes with a small benchtop compressor if it’s adequate and quieter at night than my shop compressor. 

My question’s are: 1) are the cheap kits any good?

2) should I dilute the primer and paints?

3) how should it be cleaned in between colors and before storage?

Any advice would be appreciated.

Share this post

Link to post
Share on other sites

I think I might be able to help here a bit, as I've stared using one recently. YouTube has been an awesome resource but here are a few things I picked up on my travels:

Apologies in advance, this ended up being a super long post. I've bolded the short answers to your questions:

I'd imagine at the very least a budget set up will be a huge a step up from rattle-cans. Obviously, they're not going to be as reliable or consistent as an Iwata or Badger, but the reviews should be able to tell you if they're workable. I've seen a few on Amazon where people posted photos of minis in their reviews, and I'd take that into consideration. There are a few things to keep an eye open for though:

  • Make sure it's a gravity feed brush.
  • If you can find one at a good price, get a dual action -  you'll have control over both air and paint flow simultaneously.  If you want to do anything else with this besides prime, it's worth the extra investment.
  • I went with a compressor that included a moisture trap. Not sure how optional this is - perhaps someone else can weigh in on that. 

Moving on, yes you should absolutely thin your paints, but not the airbrush primer. I found the primer didn't 'grab' or cover very well when I did. I'm using this stuff. If you're using airbrush paints for models those should come pre-thinned. 

I've been putting VA Model Color through there with their airbrush thinner and it's been fine, 1-2 coats usually does the job. (I'm still not entirely sure what the real-world difference between flow improver and airbrush thinner is.) Use a little more water than you think you need

If it gets clogged or starts acting weird, I keep a wet sponge nearby for cleaning the tip. This also comes in handy for forcing a backflow to mix paint/rinse it out. If you see bubbles in the cup and you're not doing this, it's clogged. Dump & store the paint in a spare pot and flush it out with water.

For cleaning it out afterward, it depends. I'll defer to the manual. Backflow a lot with water to get all the paint out though. Finish up with whatever the manufacturer recommends you use as a solvent and blow air through to dry it completely before storing it. I usually take the nozzle apart and soak it in cleaner for a while too. Not every time but occasionally it'll be a good idea to field strip the thing and give it a good cleaning/lubing up. Careful: don't bend that needle!

Between colors, and depending on what I'm doing, sometimes I won't bother cleaning it. You can get absolutely gorgeous gradients and color-shifts this way. Otherwise just backflow with water.

Finally, a personal horror storyI was so excited to be able to finally prime minis indoors that I underestimated just how much overspray was involved. I duct-taped myself a big cardboard shroud/booth to work in and still ended up cleaning primer dust from every square inch of the room. The floor, upholstery, curtains, bookshelf, ugh. It was everywhere, meaning there was probably a good deal inside me too. Wear a dust mask - the technicolor boogers will cease and your lungs will thank you! 

(I have since *mostly* avoided the mess by cutting the back out of the shroud and duct taping a furnace filter and a box/window fan behind it to suck air through. It's ugly as sin but works reasonably well. It's louder than the compressor though.)

There will be a learning curve but overall it's been a lot of fun and saves a boatload of time basecoating. Hope this was at least a little bit helpful, I'm no expert but I goof up a lot so feel free to ask me anything. Happy painting!

Edited by YoureNoGood2MeDeadpool

Share this post

Link to post
Share on other sites
20 hours ago, YoureNoGood2MeDeadpool said:

Hope this was at least a little bit helpful, I'm no expert but I goof up a lot so feel free to ask me anything. Happy painting!

Awesome, thanks very much!

I've found a number of youtube videos that have been pretty helpful. I've also watched Sarastro's Blood Rage Snow Giant episode which covers priming, zenithal highlights and some basics of airbrushing but it lacks some of the practical considerations that you covered nicely.

Some others have also recommended a moisture-trap. I've found one that isn't too expensive and serves as both a water-trap and regulator allow for a little more fine manipulation of the pressure. 

For paints, I was also looking at the Vallejo primers (as you suggest) and probably the Vallejo Game Air paints, very similar to your Model Air.

Based on a friends recommendation, I'm going to use my shop compressor rather than buy a cheap desktop version. I think the desktop style can work but you need a reasonably good one from what I hear.

Thanks again!

Edited by VadersMarchKazoo

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now